Aerco Modulex E8 Controls Guide Bedienungsanleitung Seite 15
- Seite / 112
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
PR1: 11/30/12 Page 15 of 112
GF-115-C
Modulex E8 Controller and BCM
Operations and Maintenance Manual
OMM-0084_0D
AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 • Ph: 800-526- 0288
Figure 3-4: E8 Display in MENU Mode (after first opening hinged door)
3.2.1 Basic Menu/Sub-Menu Navigation and Selection
Selected Menu and Sub-menu are indicated by two black arrows at display bottom pointing to
the Menu and Sub-menu names silk-screened below the display (see Figure 3-4).
Following initial startup and one-time entry of the required INSTALLATION menu items (see
E8 Controller Initial Startup, sub-section 4.7), to access, view and/or change menu items
follow these instructions:
Menu/Sub-Menu Navigation and Selection
1. When the ON/OFF switch on the front of the boiler is turned ON and the swing-down hinged
panel is opened, the controller will enter MENU Mode and INSTALLATION will be displayed
(Figure 3-4) in the LCD. This is the initial INSTALLATION menu and it is assumed that all
entries have already been made. See sub-section 4.8 for INSTALLATION menu initial entry
information.
2. Turn the Rotary Knob clockwise until the display advances to the DISPLAY menu. The dial
on the clock face will rotate one revolution counterclockwise and then go off. The display will
then show INSTALLATION, which is the first sub-menu in the DISPLAY menu group (Figure
3-4). The two small black arrows at bottom of the display will point down to the menu and
submenu names, in this case DISPLAY and INSTALLATION, respectively.
3. To view functions included in the INSTALLATION sub-menu, press the Program Key (Item
E, Figure 3-3). If desired, turn the Rotary Knob to scroll through the functions in the
INSTALLATION sub-menu. As previously mentioned, these display functions are read-only
and cannot be changed. Once you reach the end of the sub-menu, RETURN will appear in
the display.
4. To exit this sub-menu and advance to the next sub-menu in the DISPLAY menu, press the
Program Key. INSTALLATION will again be displayed. Turn the Rotary Knob clockwise until
the next sub-menu is displayed.
5. Repeat steps 2, 3 and 4 to view the remaining main menus and their associated sub-menus.
The remaining main menus are: USER, TIME PROGRAM, EXPERT, EXPERT HS (Not
Applicable to Modulex), and GENERAL.
INSTALLATION
Points down to
Selected
Sub-MENU
Name
Points right to
Selected
Buss(es)
Points left to
Selected Bus(es)
Points down to
Selected
MENU Name
Sub-MENU
Names
MENU
Names
Sub-MENU Name
- USER MANUAL 1
- Table of Contents 3
- INTRODUCTION 7
- GF-115-C 10
- Page 13 of 112 13
- 3.2 Software Menus 14
- INSTALLATION 15
- 4.1 DISPLAY Menu 18
- 4.2 USER Menu 21
- DATE/TIME 32
- Page 34 of 112 34
- Page 42 of 112 42
- 5.2 Constant Set Point Mode 43
- 6. CONNECTION DIAGRAMS 57
- Plug 2 [II] 58
- Plug 6 [VI] 58
- OMM-0084_0D 59
- Page 63 of 112 63
- 7.7 Modbus Software Set-Up 73
- 8.1 DISPLAY Menu 77
- 8.2 USER Menu 79
- 8.3 TIME PROGRAM Menu 81
- 8.4 EXPERT Menu 84
- 8.5 GENERAL Menu 89
- NOTES: 111
Verwandte Produkte und Handbücher für Ausrüstung Aerco Modulex E8 Controls Guide
(8 Seiten)
(187 Seiten)Campbell Hausfeld CHN70900 manuales
Manuales del propietario y guías del usuario para Herramientas Eléctricas Campbell Hausfeld CHN70900.
Ofrecemos 1 manuales en pdf Campbell Hausfeld CHN70900 para descargar gratis por tipos de documentos: Instrucciones de operaciones
Kommentare zu diesen Handbüchern